TY  - JOUR
AU  - Simić, Ivan
AU  - Džinčić, Igor
AU  - Palija, Tanja
PY  - 2023
UR  - https://omorika.sfb.bg.ac.rs/handle/123456789/1447
AB  - The tendency to improve the energy efficiency of windows has led to an increase in the number of panes used. The greater weight of the window sash leads to a loss of its geometry during normal usage. This deformation of geometry is caused by its own weight, and thus reduces the efficiency of preventing heat loss. All the positive effects that are obtained by using multiple panes of glass are thus lost. As window manufacturers often try to cut production costs by shortening the time of kiln drying, this paper researches the effect of using elements with different moisture content. Articles on similar topics were reviewed and it was found that there were no available data on the researched topic. Only about 20 different articles on similar topics were found, but the starting conditions or input was greatly different. Also, there are no official standards that cover the strength of window corner joints. This paper analyzes the influence of the change in moisture of the elements on the strength of the joint. Three groups of window corner joint samples were examined. The first group of samples was the control group that was supposed to determine the strength of the joint when the window beams were made with the recommended moisture according to a corresponding standard (12 +/- 2%). In the second and third groups, the moisture of the beams was taken as a variable factor, namely the moisture content of 18 +/- 2%. The results of this study show that the strength values of the currently used corner joints (double mortise and tenon) are different at different moisture contents. As expected, the samples with the recommended moisture content had higher strength values than the samples with the higher moisture content. There are many challenges in proper kiln drying and the final moisture content has a crucial impact on window strength. As windows have a specific purpose in buildings, they should have sufficient strength to be properly used over a long period. These obtained results should demonstrate the importance of the moisture content of wooden beams used in window production.
T2  - Drewno
T1  - The Influence of Moisture Content on Strength of Window Corner Joint
IS  - 212
VL  - 66
DO  - 10.53502/wood-176609
UR  - conv_1757
ER  - 

@article{
author = "Simić, Ivan and Džinčić, Igor and Palija, Tanja",
year = "2023",
abstract = "The tendency to improve the energy efficiency of windows has led to an increase in the number of panes used. The greater weight of the window sash leads to a loss of its geometry during normal usage. This deformation of geometry is caused by its own weight, and thus reduces the efficiency of preventing heat loss. All the positive effects that are obtained by using multiple panes of glass are thus lost. As window manufacturers often try to cut production costs by shortening the time of kiln drying, this paper researches the effect of using elements with different moisture content. Articles on similar topics were reviewed and it was found that there were no available data on the researched topic. Only about 20 different articles on similar topics were found, but the starting conditions or input was greatly different. Also, there are no official standards that cover the strength of window corner joints. This paper analyzes the influence of the change in moisture of the elements on the strength of the joint. Three groups of window corner joint samples were examined. The first group of samples was the control group that was supposed to determine the strength of the joint when the window beams were made with the recommended moisture according to a corresponding standard (12 +/- 2%). In the second and third groups, the moisture of the beams was taken as a variable factor, namely the moisture content of 18 +/- 2%. The results of this study show that the strength values of the currently used corner joints (double mortise and tenon) are different at different moisture contents. As expected, the samples with the recommended moisture content had higher strength values than the samples with the higher moisture content. There are many challenges in proper kiln drying and the final moisture content has a crucial impact on window strength. As windows have a specific purpose in buildings, they should have sufficient strength to be properly used over a long period. These obtained results should demonstrate the importance of the moisture content of wooden beams used in window production.",
journal = "Drewno",
title = "The Influence of Moisture Content on Strength of Window Corner Joint",
number = "212",
volume = "66",
doi = "10.53502/wood-176609",
url = "conv_1757"
}

Simić, I., Džinčić, I.,& Palija, T.. (2023). The Influence of Moisture Content on Strength of Window Corner Joint. in Drewno, 66(212).
https://doi.org/10.53502/wood-176609
conv_1757

Simić I, Džinčić I, Palija T. The Influence of Moisture Content on Strength of Window Corner Joint. in Drewno. 2023;66(212).
doi:10.53502/wood-176609
conv_1757 .

Simić, Ivan, Džinčić, Igor, Palija, Tanja, "The Influence of Moisture Content on Strength of Window Corner Joint" in Drewno, 66, no. 212 (2023),
https://doi.org/10.53502/wood-176609 .,
conv_1757 .

TY  - CONF
AU  - Džinčić, Igor
PY  - 2022
UR  - https://omorika.sfb.bg.ac.rs/handle/123456789/1342
AB  - This paper presents an analysis of a basic model of wooden chair. The aim of the paper is to optimize chair itself as joints using finite element analysis. Contact forces and deformations of two mostly used joints in furniture industry: oval tenon and a mortise, and dowel and a hole was analysed. The theoretical analysis was performed using the finite elements method, whereas experimental verification of the results, was obtained by invasive methods by testing samples on rigidity and durability according to European norms. Verification of the obtained stresses and strains was carried out using strain gauges positioned on chair samples. During the production of test pieces types of fit and types of joints were varied. Presented results showed that connection between side rail and rear leg presents the most critical spot in chair construction. Comparative analysis of the results obtained by finite element method and rigidity tests, showed that setup of parameters during finite element analysis was well done and presents recommendations for further research.
PB  - Springer Science and Business Media Deutschland GmbH
C3  - Lecture Notes in Networks and Systems
T1  - A FEM Analysis of Mortise and Tenon Joint Within Chairs
EP  - 17
SP  - 1
VL  - 323
DO  - 10.1007/978-3-030-86009-7_1
UR  - conv_1950
ER  - 

@conference{
author = "Džinčić, Igor",
year = "2022",
abstract = "This paper presents an analysis of a basic model of wooden chair. The aim of the paper is to optimize chair itself as joints using finite element analysis. Contact forces and deformations of two mostly used joints in furniture industry: oval tenon and a mortise, and dowel and a hole was analysed. The theoretical analysis was performed using the finite elements method, whereas experimental verification of the results, was obtained by invasive methods by testing samples on rigidity and durability according to European norms. Verification of the obtained stresses and strains was carried out using strain gauges positioned on chair samples. During the production of test pieces types of fit and types of joints were varied. Presented results showed that connection between side rail and rear leg presents the most critical spot in chair construction. Comparative analysis of the results obtained by finite element method and rigidity tests, showed that setup of parameters during finite element analysis was well done and presents recommendations for further research.",
publisher = "Springer Science and Business Media Deutschland GmbH",
journal = "Lecture Notes in Networks and Systems",
title = "A FEM Analysis of Mortise and Tenon Joint Within Chairs",
pages = "17-1",
volume = "323",
doi = "10.1007/978-3-030-86009-7_1",
url = "conv_1950"
}

Džinčić, I.. (2022). A FEM Analysis of Mortise and Tenon Joint Within Chairs. in Lecture Notes in Networks and Systems
Springer Science and Business Media Deutschland GmbH., 323, 1-17.
https://doi.org/10.1007/978-3-030-86009-7_1
conv_1950

Džinčić I. A FEM Analysis of Mortise and Tenon Joint Within Chairs. in Lecture Notes in Networks and Systems. 2022;323:1-17.
doi:10.1007/978-3-030-86009-7_1
conv_1950 .

Džinčić, Igor, "A FEM Analysis of Mortise and Tenon Joint Within Chairs" in Lecture Notes in Networks and Systems, 323 (2022):1-17,
https://doi.org/10.1007/978-3-030-86009-7_1 .,
conv_1950 .

TY  - JOUR
AU  - Džinčić, Igor
AU  - Palija, Tanja
AU  - Zivanić, Dragan
AU  - Dacić, Vojislav
PY  - 2021
UR  - https://omorika.sfb.bg.ac.rs/handle/123456789/1197
AB  - The objective of this study was to investigate the relation of diameter of pilot hole and screw, and machining accuracy on withdrawal strengths of the screws and durability of the dining tables. For this purpose, fasteners and material types on the failure loads of dining table corner joints have been analyzed experimentally and statistically. Double ended thread bolts with different drilling regimes have been used as fastener types. A parallel investigation of rigidity and durability of tables, and withdrawal capacities in accordance with the according to current norms, was performed. According to the results, it is concluded that the diameter of the drilled hole significantly influences the value of the withdrawal strengths of the screws. By analyzing the effect of drilling diameter on the rigidity of tables, a statistically significant difference was determined. As the drilling diameter increases, the rigidity of the examined dining tables decreases.
T2  - Maderas-Ciencia Y Tecnologia
T1  - Determination of the strength performance of table frames
VL  - 23
DO  - 10.4067/s0718-221x2021000100461
UR  - conv_1600
ER  - 

@article{
author = "Džinčić, Igor and Palija, Tanja and Zivanić, Dragan and Dacić, Vojislav",
year = "2021",
abstract = "The objective of this study was to investigate the relation of diameter of pilot hole and screw, and machining accuracy on withdrawal strengths of the screws and durability of the dining tables. For this purpose, fasteners and material types on the failure loads of dining table corner joints have been analyzed experimentally and statistically. Double ended thread bolts with different drilling regimes have been used as fastener types. A parallel investigation of rigidity and durability of tables, and withdrawal capacities in accordance with the according to current norms, was performed. According to the results, it is concluded that the diameter of the drilled hole significantly influences the value of the withdrawal strengths of the screws. By analyzing the effect of drilling diameter on the rigidity of tables, a statistically significant difference was determined. As the drilling diameter increases, the rigidity of the examined dining tables decreases.",
journal = "Maderas-Ciencia Y Tecnologia",
title = "Determination of the strength performance of table frames",
volume = "23",
doi = "10.4067/s0718-221x2021000100461",
url = "conv_1600"
}

Džinčić, I., Palija, T., Zivanić, D.,& Dacić, V.. (2021). Determination of the strength performance of table frames. in Maderas-Ciencia Y Tecnologia, 23.
https://doi.org/10.4067/s0718-221x2021000100461
conv_1600

Džinčić I, Palija T, Zivanić D, Dacić V. Determination of the strength performance of table frames. in Maderas-Ciencia Y Tecnologia. 2021;23.
doi:10.4067/s0718-221x2021000100461
conv_1600 .

Džinčić, Igor, Palija, Tanja, Zivanić, Dragan, Dacić, Vojislav, "Determination of the strength performance of table frames" in Maderas-Ciencia Y Tecnologia, 23 (2021),
https://doi.org/10.4067/s0718-221x2021000100461 .,
conv_1600 .

TY  - CONF
AU  - Petrović, Slavica
AU  - Džinčić, Igor
PY  - 2019
UR  - https://omorika.sfb.bg.ac.rs/handle/123456789/1033
AB  - During the period 2004-2018, the EU-28 countries increased the import value of upholstered wooden chairs for 35.1% up to (sic)5.4 billion. Germany, France and the United Kingdom represent the biggest importers of this product in the EU-28, having reached the import value of (sic)3.2 billion in 2018. The most important countries supplying above mentioned countries are Poland and China. Serbia, as a non EU-28 country, participates with small share in the EU market supply with upholstered wooden chairs. The most important EU-28 markets for export from Serbia are Slovenia, the Netherlands, Italy, Croatia and Germany. Except for the international trade flow, the paper also deals with the analysis of the specific requirements of certain markets referring to the quality of chairs, as well as their components.
PB  - Union of Scientists of Bulgaria and WoodEMA, i.a.
C3  - Digitalisation and Circular Economy: Forestry and Forestry Based Industry Implications - Proceedings of Scientific Papers
T1  - The EU-28 market of upholstered wooden chairs
EP  - 308
SP  - 303
UR  - conv_2027
ER  - 

@conference{
author = "Petrović, Slavica and Džinčić, Igor",
year = "2019",
abstract = "During the period 2004-2018, the EU-28 countries increased the import value of upholstered wooden chairs for 35.1% up to (sic)5.4 billion. Germany, France and the United Kingdom represent the biggest importers of this product in the EU-28, having reached the import value of (sic)3.2 billion in 2018. The most important countries supplying above mentioned countries are Poland and China. Serbia, as a non EU-28 country, participates with small share in the EU market supply with upholstered wooden chairs. The most important EU-28 markets for export from Serbia are Slovenia, the Netherlands, Italy, Croatia and Germany. Except for the international trade flow, the paper also deals with the analysis of the specific requirements of certain markets referring to the quality of chairs, as well as their components.",
publisher = "Union of Scientists of Bulgaria and WoodEMA, i.a.",
journal = "Digitalisation and Circular Economy: Forestry and Forestry Based Industry Implications - Proceedings of Scientific Papers",
title = "The EU-28 market of upholstered wooden chairs",
pages = "308-303",
url = "conv_2027"
}

Petrović, S.,& Džinčić, I.. (2019). The EU-28 market of upholstered wooden chairs. in Digitalisation and Circular Economy: Forestry and Forestry Based Industry Implications - Proceedings of Scientific Papers
Union of Scientists of Bulgaria and WoodEMA, i.a.., 303-308.
conv_2027

Petrović S, Džinčić I. The EU-28 market of upholstered wooden chairs. in Digitalisation and Circular Economy: Forestry and Forestry Based Industry Implications - Proceedings of Scientific Papers. 2019;:303-308.
conv_2027 .

Petrović, Slavica, Džinčić, Igor, "The EU-28 market of upholstered wooden chairs" in Digitalisation and Circular Economy: Forestry and Forestry Based Industry Implications - Proceedings of Scientific Papers (2019):303-308,
conv_2027 .

TY  - JOUR
AU  - Palija, Tanja
AU  - Jaić, Milan
AU  - Džinčić, Igor
AU  - Sucur, Aleksandra
AU  - Dobić, Jovan
PY  - 2018
UR  - https://omorika.sfb.bg.ac.rs/handle/123456789/950
AB  - This study investigates variation in the dry film thickness (DFT) of a coating applied by roller coater on the surface of wood in real industrial conditions on a UV finishing line. It was examined how DFT is influenced by the temperature of the liquid top coating, the position of the sample on the conveyor, and the position of the measurement point along the length of the sample. The three-way interaction between the temperature of the liquid top coating, position on the conveyor and position along the sample did not have a statistically significant impact on DFT. However, an increase in the temperature of the liquid top coating (from 24.1 to 24.8 degrees C) caused a decrease in the viscosity of the coating and a significant reduction in DFT when samples were positioned closer to the coating supply hose or in the middle of the conveyor. When the temperature of the liquid top coating was lower, the variation in DFT at different positions across the conveyor was not significant. A higher temperature of liquid top coating led to significantly smaller DFT for samples closer to the supply hose and in the middle, compared with those further from the supply hose. It was also found that DFT was greater at the forward end then at the back end of sample.
T2  - Drewno
T1  - Variability of dry film thickness of a coating applied by roller coater on wood in a real industrial process
EP  - 164
IS  - 201
SP  - 153
VL  - 61
DO  - 10.12841/wood.1644-3985.251.13
UR  - conv_1368
ER  - 

@article{
author = "Palija, Tanja and Jaić, Milan and Džinčić, Igor and Sucur, Aleksandra and Dobić, Jovan",
year = "2018",
abstract = "This study investigates variation in the dry film thickness (DFT) of a coating applied by roller coater on the surface of wood in real industrial conditions on a UV finishing line. It was examined how DFT is influenced by the temperature of the liquid top coating, the position of the sample on the conveyor, and the position of the measurement point along the length of the sample. The three-way interaction between the temperature of the liquid top coating, position on the conveyor and position along the sample did not have a statistically significant impact on DFT. However, an increase in the temperature of the liquid top coating (from 24.1 to 24.8 degrees C) caused a decrease in the viscosity of the coating and a significant reduction in DFT when samples were positioned closer to the coating supply hose or in the middle of the conveyor. When the temperature of the liquid top coating was lower, the variation in DFT at different positions across the conveyor was not significant. A higher temperature of liquid top coating led to significantly smaller DFT for samples closer to the supply hose and in the middle, compared with those further from the supply hose. It was also found that DFT was greater at the forward end then at the back end of sample.",
journal = "Drewno",
title = "Variability of dry film thickness of a coating applied by roller coater on wood in a real industrial process",
pages = "164-153",
number = "201",
volume = "61",
doi = "10.12841/wood.1644-3985.251.13",
url = "conv_1368"
}

Palija, T., Jaić, M., Džinčić, I., Sucur, A.,& Dobić, J.. (2018). Variability of dry film thickness of a coating applied by roller coater on wood in a real industrial process. in Drewno, 61(201), 153-164.
https://doi.org/10.12841/wood.1644-3985.251.13
conv_1368

Palija T, Jaić M, Džinčić I, Sucur A, Dobić J. Variability of dry film thickness of a coating applied by roller coater on wood in a real industrial process. in Drewno. 2018;61(201):153-164.
doi:10.12841/wood.1644-3985.251.13
conv_1368 .

Palija, Tanja, Jaić, Milan, Džinčić, Igor, Sucur, Aleksandra, Dobić, Jovan, "Variability of dry film thickness of a coating applied by roller coater on wood in a real industrial process" in Drewno, 61, no. 201 (2018):153-164,
https://doi.org/10.12841/wood.1644-3985.251.13 .,
conv_1368 .

TY  - JOUR
AU  - Zdravković, Vladislav
AU  - Lovrić, Aleksandar
AU  - Džinčić, Igor
AU  - Pantović, Nemanja
PY  - 2017
UR  - https://omorika.sfb.bg.ac.rs/handle/123456789/851
AB  - Predmet ovog rada je ispitivanje fizičkih i mehaničkih svojstava topolovih LVL ploča spolja dodatno ojačanih bukovim furnirom, kao i ispitivanje čvrstoće ugaonih elemenata veze za prozor izrađenih od ovog materijala. Ploče su presovane suvim vrućim postupkom u industrijskim uslovima, a kao vezivno sredstvo korišćen je FF fenol - formaldehidni lepak. Uzorci za ispitivanje čvrstoće ugaonih spojeva spajani su dvostrukim prizmatičnim čepom i prorezom pomoću PVA-c lepka klase D4. Statistička analiza pokazala je da postoji značajna razlika u vlažnosti i gustini ploča po debljinama dok kod tvrdoće ploča značajnost razlike ne postoji. Rezultati smicajne čvrstoće u sloju lepka pokazali su da su i FF i PVA-c D4 lepak ispunili uslove propisane standardom. Podaci dobijeni ispitivanjem elementa veze za prozor pokazali su da spoj dvostruki čep i prorez spojen pomoću PVA-c lepka tip D4, u potpunosti može primeniti u proizvodnji i eksploataciji prozora pojačane nosivosti.
AB  - The subject of this paper was a research of physical and mechanical properties of LVL composed of peeled poplar veneers in core layers and only outer layers of beech peeled veneers, so as the examination of window frame glue joint strength produced of this material. LVL boards have been hot pressed in industrial conditions, using appropriate phenol formaldehyde (PP) adhesive. Samples for corner window frame glue joint strength testing were glued with PVAc D4 class adhesive. Statistical analysis showed that there were significant differences both in moisture content and density of LVL boards regarding their thickness, while in the case of hardness this difference did not exist. Examinations of LVL glue line shear strength showed that both phenol formaldehyde (PP) and PVAc D4 class adhesives fulfilled standard requirements. The results of corner window frame double tenon glue joint strength produced from combined poplar-beech veneer LVL indicated that such material could be used to produce window frame corner joint, strong enough to withstand the additional load, without an increase of the cross section.
PB  - Univerzitet u Beogradu - Šumarski fakultet, Beograd
T2  - Glasnik Šumarskog fakulteta
T1  - Svojstva i mogućnost upotrebe kombinovanog LVL-a topole i bukve za izradu prozorskih okvira
T1  - Some properties of LVL composed of poplar and beech veneer and possibilities of their application for window frames
EP  - 184
IS  - 115
SP  - 167
DO  - 10.2298/GSF1715167Z
UR  - conv_459
ER  - 

@article{
author = "Zdravković, Vladislav and Lovrić, Aleksandar and Džinčić, Igor and Pantović, Nemanja",
year = "2017",
abstract = "Predmet ovog rada je ispitivanje fizičkih i mehaničkih svojstava topolovih LVL ploča spolja dodatno ojačanih bukovim furnirom, kao i ispitivanje čvrstoće ugaonih elemenata veze za prozor izrađenih od ovog materijala. Ploče su presovane suvim vrućim postupkom u industrijskim uslovima, a kao vezivno sredstvo korišćen je FF fenol - formaldehidni lepak. Uzorci za ispitivanje čvrstoće ugaonih spojeva spajani su dvostrukim prizmatičnim čepom i prorezom pomoću PVA-c lepka klase D4. Statistička analiza pokazala je da postoji značajna razlika u vlažnosti i gustini ploča po debljinama dok kod tvrdoće ploča značajnost razlike ne postoji. Rezultati smicajne čvrstoće u sloju lepka pokazali su da su i FF i PVA-c D4 lepak ispunili uslove propisane standardom. Podaci dobijeni ispitivanjem elementa veze za prozor pokazali su da spoj dvostruki čep i prorez spojen pomoću PVA-c lepka tip D4, u potpunosti može primeniti u proizvodnji i eksploataciji prozora pojačane nosivosti., The subject of this paper was a research of physical and mechanical properties of LVL composed of peeled poplar veneers in core layers and only outer layers of beech peeled veneers, so as the examination of window frame glue joint strength produced of this material. LVL boards have been hot pressed in industrial conditions, using appropriate phenol formaldehyde (PP) adhesive. Samples for corner window frame glue joint strength testing were glued with PVAc D4 class adhesive. Statistical analysis showed that there were significant differences both in moisture content and density of LVL boards regarding their thickness, while in the case of hardness this difference did not exist. Examinations of LVL glue line shear strength showed that both phenol formaldehyde (PP) and PVAc D4 class adhesives fulfilled standard requirements. The results of corner window frame double tenon glue joint strength produced from combined poplar-beech veneer LVL indicated that such material could be used to produce window frame corner joint, strong enough to withstand the additional load, without an increase of the cross section.",
publisher = "Univerzitet u Beogradu - Šumarski fakultet, Beograd",
journal = "Glasnik Šumarskog fakulteta",
title = "Svojstva i mogućnost upotrebe kombinovanog LVL-a topole i bukve za izradu prozorskih okvira, Some properties of LVL composed of poplar and beech veneer and possibilities of their application for window frames",
pages = "184-167",
number = "115",
doi = "10.2298/GSF1715167Z",
url = "conv_459"
}

Zdravković, V., Lovrić, A., Džinčić, I.,& Pantović, N.. (2017). Svojstva i mogućnost upotrebe kombinovanog LVL-a topole i bukve za izradu prozorskih okvira. in Glasnik Šumarskog fakulteta
Univerzitet u Beogradu - Šumarski fakultet, Beograd.(115), 167-184.
https://doi.org/10.2298/GSF1715167Z
conv_459

Zdravković V, Lovrić A, Džinčić I, Pantović N. Svojstva i mogućnost upotrebe kombinovanog LVL-a topole i bukve za izradu prozorskih okvira. in Glasnik Šumarskog fakulteta. 2017;(115):167-184.
doi:10.2298/GSF1715167Z
conv_459 .

Zdravković, Vladislav, Lovrić, Aleksandar, Džinčić, Igor, Pantović, Nemanja, "Svojstva i mogućnost upotrebe kombinovanog LVL-a topole i bukve za izradu prozorskih okvira" in Glasnik Šumarskog fakulteta, no. 115 (2017):167-184,
https://doi.org/10.2298/GSF1715167Z .,
conv_459 .

TY  - JOUR
AU  - Džinčić, Igor
AU  - Palija, Tanja
AU  - Mirić-Milosavljević, Mira
AU  - Mihailović, Vladislava
PY  - 2017
UR  - https://omorika.sfb.bg.ac.rs/handle/123456789/829
AB  - The variations in number and method of applied joints within storage furniture gave idea for this investigation. Importance of joint selection and its geometrical characteristic is clear if we bear in mind that the joints are critical points in the structure, and the rigidity and durability of storage furniture are in direct correlation with the type of the applied joint. Results presented in scientific papers provide little useful information to the engineer for the safe selection of the optimal joint. Number of joints along the connecting line (depth of the box type element) engineers determined empirically. In order to define stress state in the storage furniture, data on size of the load, that the box element has to with stand during its use, should be determined. The aim of this study was to determine the size and character of the loads in corner joints in storage furniture. Based on this data, as well as on the basis of information about the strength of the corner joints it is possible to calculate the required number of appropriate joining elements for each separate case.
PB  - Statny Drevarsky Vyskumny Ustav
T2  - Wood Research
T1  - Size and character of the loads in corner joints within storage furniture
EP  - 458
IS  - 3
SP  - 451
VL  - 62
UR  - conv_2061
ER  - 

@article{
author = "Džinčić, Igor and Palija, Tanja and Mirić-Milosavljević, Mira and Mihailović, Vladislava",
year = "2017",
abstract = "The variations in number and method of applied joints within storage furniture gave idea for this investigation. Importance of joint selection and its geometrical characteristic is clear if we bear in mind that the joints are critical points in the structure, and the rigidity and durability of storage furniture are in direct correlation with the type of the applied joint. Results presented in scientific papers provide little useful information to the engineer for the safe selection of the optimal joint. Number of joints along the connecting line (depth of the box type element) engineers determined empirically. In order to define stress state in the storage furniture, data on size of the load, that the box element has to with stand during its use, should be determined. The aim of this study was to determine the size and character of the loads in corner joints in storage furniture. Based on this data, as well as on the basis of information about the strength of the corner joints it is possible to calculate the required number of appropriate joining elements for each separate case.",
publisher = "Statny Drevarsky Vyskumny Ustav",
journal = "Wood Research",
title = "Size and character of the loads in corner joints within storage furniture",
pages = "458-451",
number = "3",
volume = "62",
url = "conv_2061"
}

Džinčić, I., Palija, T., Mirić-Milosavljević, M.,& Mihailović, V.. (2017). Size and character of the loads in corner joints within storage furniture. in Wood Research
Statny Drevarsky Vyskumny Ustav., 62(3), 451-458.
conv_2061

Džinčić I, Palija T, Mirić-Milosavljević M, Mihailović V. Size and character of the loads in corner joints within storage furniture. in Wood Research. 2017;62(3):451-458.
conv_2061 .

Džinčić, Igor, Palija, Tanja, Mirić-Milosavljević, Mira, Mihailović, Vladislava, "Size and character of the loads in corner joints within storage furniture" in Wood Research, 62, no. 3 (2017):451-458,
conv_2061 .

TY  - JOUR
AU  - Džinčić, Igor
AU  - Nestorović, Biserka
AU  - Dacić, Vojislav
PY  - 2016
UR  - https://omorika.sfb.bg.ac.rs/handle/123456789/739
AB  - U radu su prikazani rezultati uporednog ispitivanja čvrstoće spojeva ovalni čep-žljeb kod dve grupe proba. Spojevi grupe A, izrađivani su sa oba ramena čepa, dok su spojevi grupe B izrađivani bez donjeg ramena čepa. Ispitivanje čvrstoće, sprovedeno je na spojevima bočnog sarga i zadnje noge stolice. Rezultati istraživanja su pokazali da spojevi grupe A imaju veću prosečnu vrednost momenta savijanja u odnosu na spojeve grupe B, ali statističkom analizom nije potvrđena značajnost razlike u čvrstoći između ove dve grupe spojeva.
AB  - This paper presents the results of a parallel examination on the strength of oval tenonmortise joints in two groups of test joints. Joints from group A were made with both shoulders of tenon, while joints from group B were made without the lower shoulder. Examination of strength was conducted on a chair joints rear leg-rail. The results of the examination indicated that joints in group A had a higher average bending moment capacity in comparison with the joints in group B. However, the significance of difference in strength between the two groups of joints was not confirmed by the statistical analysis.
PB  - Univerzitet u Beogradu - Šumarski fakultet, Beograd
T2  - Glasnik Šumarskog fakulteta
T1  - Uticaj ramena čepa na čvrstoću spoja ovalni čep-žljeb
T1  - The effect of shoulder on the strength of the oval tenon-mortise joint
EP  - 46
IS  - 113
SP  - 35
DO  - 10.2298/GSF151109001D
UR  - conv_435
ER  - 

@article{
author = "Džinčić, Igor and Nestorović, Biserka and Dacić, Vojislav",
year = "2016",
abstract = "U radu su prikazani rezultati uporednog ispitivanja čvrstoće spojeva ovalni čep-žljeb kod dve grupe proba. Spojevi grupe A, izrađivani su sa oba ramena čepa, dok su spojevi grupe B izrađivani bez donjeg ramena čepa. Ispitivanje čvrstoće, sprovedeno je na spojevima bočnog sarga i zadnje noge stolice. Rezultati istraživanja su pokazali da spojevi grupe A imaju veću prosečnu vrednost momenta savijanja u odnosu na spojeve grupe B, ali statističkom analizom nije potvrđena značajnost razlike u čvrstoći između ove dve grupe spojeva., This paper presents the results of a parallel examination on the strength of oval tenonmortise joints in two groups of test joints. Joints from group A were made with both shoulders of tenon, while joints from group B were made without the lower shoulder. Examination of strength was conducted on a chair joints rear leg-rail. The results of the examination indicated that joints in group A had a higher average bending moment capacity in comparison with the joints in group B. However, the significance of difference in strength between the two groups of joints was not confirmed by the statistical analysis.",
publisher = "Univerzitet u Beogradu - Šumarski fakultet, Beograd",
journal = "Glasnik Šumarskog fakulteta",
title = "Uticaj ramena čepa na čvrstoću spoja ovalni čep-žljeb, The effect of shoulder on the strength of the oval tenon-mortise joint",
pages = "46-35",
number = "113",
doi = "10.2298/GSF151109001D",
url = "conv_435"
}

Džinčić, I., Nestorović, B.,& Dacić, V.. (2016). Uticaj ramena čepa na čvrstoću spoja ovalni čep-žljeb. in Glasnik Šumarskog fakulteta
Univerzitet u Beogradu - Šumarski fakultet, Beograd.(113), 35-46.
https://doi.org/10.2298/GSF151109001D
conv_435

Džinčić I, Nestorović B, Dacić V. Uticaj ramena čepa na čvrstoću spoja ovalni čep-žljeb. in Glasnik Šumarskog fakulteta. 2016;(113):35-46.
doi:10.2298/GSF151109001D
conv_435 .

Džinčić, Igor, Nestorović, Biserka, Dacić, Vojislav, "Uticaj ramena čepa na čvrstoću spoja ovalni čep-žljeb" in Glasnik Šumarskog fakulteta, no. 113 (2016):35-46,
https://doi.org/10.2298/GSF151109001D .,
conv_435 .

TY  - JOUR
AU  - Džinčić, Igor
AU  - Zivanić, Dragan
PY  - 2014
UR  - https://omorika.sfb.bg.ac.rs/handle/123456789/593
AB  - The analysis of spatial furniture with Finite element method (FEM) provides answers to many engineering problems. One of the fields which is not wholly solved is analysis of glued joints. In order to analyze joints by FEM it is necessary to have access to data on size and type of deformation which occurs as a result of overlap type of fit as well as data on thickness of the glue layer in joint. This paper provides answers to the impact of fit on the distribution of glue in the gluing surface. Test were conducted on oval mortise and tenon joint. The thickness of the glue line was measured on 800 samples. Based on the results the overlap occurred in the majority of samples (over 80 %). Average value of the thickness of the joint zone impregnated by glue amounted to 0.07 mm.
PB  - Statny Drevarsky Vyskumny Ustav
T2  - Wood Research
T1  - The influence of fit on the distribution of glue in oval tenon/mortise joint
EP  - 302
IS  - 2
SP  - 297
VL  - 59
UR  - conv_2092
ER  - 

@article{
author = "Džinčić, Igor and Zivanić, Dragan",
year = "2014",
abstract = "The analysis of spatial furniture with Finite element method (FEM) provides answers to many engineering problems. One of the fields which is not wholly solved is analysis of glued joints. In order to analyze joints by FEM it is necessary to have access to data on size and type of deformation which occurs as a result of overlap type of fit as well as data on thickness of the glue layer in joint. This paper provides answers to the impact of fit on the distribution of glue in the gluing surface. Test were conducted on oval mortise and tenon joint. The thickness of the glue line was measured on 800 samples. Based on the results the overlap occurred in the majority of samples (over 80 %). Average value of the thickness of the joint zone impregnated by glue amounted to 0.07 mm.",
publisher = "Statny Drevarsky Vyskumny Ustav",
journal = "Wood Research",
title = "The influence of fit on the distribution of glue in oval tenon/mortise joint",
pages = "302-297",
number = "2",
volume = "59",
url = "conv_2092"
}

Džinčić, I.,& Zivanić, D.. (2014). The influence of fit on the distribution of glue in oval tenon/mortise joint. in Wood Research
Statny Drevarsky Vyskumny Ustav., 59(2), 297-302.
conv_2092

Džinčić I, Zivanić D. The influence of fit on the distribution of glue in oval tenon/mortise joint. in Wood Research. 2014;59(2):297-302.
conv_2092 .

Džinčić, Igor, Zivanić, Dragan, "The influence of fit on the distribution of glue in oval tenon/mortise joint" in Wood Research, 59, no. 2 (2014):297-302,
conv_2092 .

TY  - JOUR
AU  - Džinčić, Igor
AU  - Palija, Tanja
AU  - Pavlović, Dragan
PY  - 2012
UR  - https://omorika.sfb.bg.ac.rs/handle/123456789/453
AB  - Za razliku od mekih vrsta drveća, podaci o dužinskom nastavljanju tvrdih lišćara su veoma oskudni. Cilj ovog rada je da se ispita uticaj šeme opterećenja na savojnu čvrstoću bukovih gredica nastavljenih pomoću klinasto zupčaste veze. Sa stanovišta konstrukcije klinasto zupčasti spojevi predstavljaju osnovni način dužinskog nastavljanja gredica prilikom izrade lameliranih elemenata. Ispitivanje savojne čvrstoće dužinski nastavljenih gredica od tvrdog drveta na teritoriji Srbije gotovo da nije ni vršeno. Ispitivana su dva profila klinasto-zupčastih spojeva u skladu sa DIN68140. Klinasto-zupčasti spojevi su izrađivani po boku i po stranici gredica. Uzorci nastavljeni po dužini opterećivani su i po boku i po stranici. Na osnovu dobijenih rezultata došlo se do zaključaka da pravac opterećenja, površina lepljenja kao i položaj spoja utiču na čvrstoću dužinski nastavljenih gredica.
AB  - Limited information is available on end gluing hardwoods in contrast to softwoods, which have been extensively investigated. The objective of this study was to examine the influence of bending pattern on bending strength of finger jointed beech wood. In structural uses finger jointing is finally the major method to end joint timber for the production of glue-laminated elements. There are no bending strength experimental results for finger-jointed hardwoods for investigations conducted in Serbia. Two finger jointed profiles were studied in accordance with DIN68140. The finger joints were made by side and by face of beam. Length jointed samples were loaded at the side and in the face. The obtained results led to the conclusion that the direction of load, gluing surface and the position of joint influence on the strength of continued longitudinal beams.
PB  - Univerzitet u Beogradu - Šumarski fakultet, Beograd
T2  - Glasnik Šumarskog fakulteta
T1  - Uticaj šeme opterećenja na čvrstoću klinasto-zupčastih spojeva
T1  - Effect of bending pattern on finger joint bending strength
EP  - 80
IS  - 105
SP  - 73
DO  - 10.2298/GSF1205073D
UR  - conv_358
ER  - 

@article{
author = "Džinčić, Igor and Palija, Tanja and Pavlović, Dragan",
year = "2012",
abstract = "Za razliku od mekih vrsta drveća, podaci o dužinskom nastavljanju tvrdih lišćara su veoma oskudni. Cilj ovog rada je da se ispita uticaj šeme opterećenja na savojnu čvrstoću bukovih gredica nastavljenih pomoću klinasto zupčaste veze. Sa stanovišta konstrukcije klinasto zupčasti spojevi predstavljaju osnovni način dužinskog nastavljanja gredica prilikom izrade lameliranih elemenata. Ispitivanje savojne čvrstoće dužinski nastavljenih gredica od tvrdog drveta na teritoriji Srbije gotovo da nije ni vršeno. Ispitivana su dva profila klinasto-zupčastih spojeva u skladu sa DIN68140. Klinasto-zupčasti spojevi su izrađivani po boku i po stranici gredica. Uzorci nastavljeni po dužini opterećivani su i po boku i po stranici. Na osnovu dobijenih rezultata došlo se do zaključaka da pravac opterećenja, površina lepljenja kao i položaj spoja utiču na čvrstoću dužinski nastavljenih gredica., Limited information is available on end gluing hardwoods in contrast to softwoods, which have been extensively investigated. The objective of this study was to examine the influence of bending pattern on bending strength of finger jointed beech wood. In structural uses finger jointing is finally the major method to end joint timber for the production of glue-laminated elements. There are no bending strength experimental results for finger-jointed hardwoods for investigations conducted in Serbia. Two finger jointed profiles were studied in accordance with DIN68140. The finger joints were made by side and by face of beam. Length jointed samples were loaded at the side and in the face. The obtained results led to the conclusion that the direction of load, gluing surface and the position of joint influence on the strength of continued longitudinal beams.",
publisher = "Univerzitet u Beogradu - Šumarski fakultet, Beograd",
journal = "Glasnik Šumarskog fakulteta",
title = "Uticaj šeme opterećenja na čvrstoću klinasto-zupčastih spojeva, Effect of bending pattern on finger joint bending strength",
pages = "80-73",
number = "105",
doi = "10.2298/GSF1205073D",
url = "conv_358"
}

Džinčić, I., Palija, T.,& Pavlović, D.. (2012). Uticaj šeme opterećenja na čvrstoću klinasto-zupčastih spojeva. in Glasnik Šumarskog fakulteta
Univerzitet u Beogradu - Šumarski fakultet, Beograd.(105), 73-80.
https://doi.org/10.2298/GSF1205073D
conv_358

Džinčić I, Palija T, Pavlović D. Uticaj šeme opterećenja na čvrstoću klinasto-zupčastih spojeva. in Glasnik Šumarskog fakulteta. 2012;(105):73-80.
doi:10.2298/GSF1205073D
conv_358 .

Džinčić, Igor, Palija, Tanja, Pavlović, Dragan, "Uticaj šeme opterećenja na čvrstoću klinasto-zupčastih spojeva" in Glasnik Šumarskog fakulteta, no. 105 (2012):73-80,
https://doi.org/10.2298/GSF1205073D .,
conv_358 .

TY  - JOUR
AU  - Džinčić, Igor
AU  - Skakić, Dušan
PY  - 2012
UR  - https://omorika.sfb.bg.ac.rs/handle/123456789/468
AB  - Machinability has been defined, in a general way, as an ability of a certain structural material to be machined by cutting or deformation through common, economical production techniques and technologies. However, a significant disadvantage of this definition is that it does not define the way in which this ability (machinability) is quantified and measured. This research deals with with ways of determining numerical values of parameters of machinability during the process of machining oak wood by longitudinal routing. In order to determine the factors of machinability in the function of tangential cutting force the authors used multifactor orthogonal linear plan of experiment. Analyzing the position of straight lines in the given diagrams and the values of the exponents in the model the following can be concluded: Average tangential cutting force increases with the increase of any of the analyzed factors; With regard to intensity, cutting depth has a greater effect on the cutting force; If the cutting depth increases, the increase of cutting force is faster when feed per edge is greater. If the feed per edge is increased, the increase of tangential cutting force is more significant when the value of cutting depth is greater.
T2  - Wood Research
T1  - Determining the parameters of wood machinabilityas a function of tangential cutting force during the process of machining wood by routing
EP  - 172
IS  - 1
SP  - 161
VL  - 57
UR  - conv_2206
ER  - 

@article{
author = "Džinčić, Igor and Skakić, Dušan",
year = "2012",
abstract = "Machinability has been defined, in a general way, as an ability of a certain structural material to be machined by cutting or deformation through common, economical production techniques and technologies. However, a significant disadvantage of this definition is that it does not define the way in which this ability (machinability) is quantified and measured. This research deals with with ways of determining numerical values of parameters of machinability during the process of machining oak wood by longitudinal routing. In order to determine the factors of machinability in the function of tangential cutting force the authors used multifactor orthogonal linear plan of experiment. Analyzing the position of straight lines in the given diagrams and the values of the exponents in the model the following can be concluded: Average tangential cutting force increases with the increase of any of the analyzed factors; With regard to intensity, cutting depth has a greater effect on the cutting force; If the cutting depth increases, the increase of cutting force is faster when feed per edge is greater. If the feed per edge is increased, the increase of tangential cutting force is more significant when the value of cutting depth is greater.",
journal = "Wood Research",
title = "Determining the parameters of wood machinabilityas a function of tangential cutting force during the process of machining wood by routing",
pages = "172-161",
number = "1",
volume = "57",
url = "conv_2206"
}

Džinčić, I.,& Skakić, D.. (2012). Determining the parameters of wood machinabilityas a function of tangential cutting force during the process of machining wood by routing. in Wood Research, 57(1), 161-172.
conv_2206

Džinčić I, Skakić D. Determining the parameters of wood machinabilityas a function of tangential cutting force during the process of machining wood by routing. in Wood Research. 2012;57(1):161-172.
conv_2206 .

Džinčić, Igor, Skakić, Dušan, "Determining the parameters of wood machinabilityas a function of tangential cutting force during the process of machining wood by routing" in Wood Research, 57, no. 1 (2012):161-172,
conv_2206 .

TY  - JOUR
AU  - Džinčić, Igor
AU  - Skakić, Dušan
PY  - 2012
UR  - https://omorika.sfb.bg.ac.rs/handle/123456789/465
AB  - Only a few studies were found in which joints are taken into consideration while analyzing spatial furniture by usage of finite element method. This paper presents results of effects of type of fit on strength of oval tenon-mortise. When calculation are to be made in solid-mechanics, specific input parameters must be defined. In most modern finite element software's Young's modulus of elasticity is one of the basic data. The type of strain, which is result of the fit with splice, has impact on the changes in the Young's modulus of elasticity, which is the basic parameter in the defining of the material of the model. Aim of this study is to define rate of deformation of oval tenon-mortise joint as a result of fitting influence. Type and size of strains which occur in a joint in case of the fit with splice were examined with templates which were set on a joint. Based on this study results, the type of fit has influence on strength of the joints. In the presence of the fit with splice, a permanent change in the dimensions of the plug and hole will occur. During joining of joints with a splice fit, most strains belong to the group of elastic strains, which by all means contributes to the joint strength.
T2  - Wood Research
T1  - Influence of type of fit on strength and deformation of oval tenon-mortise joint
EP  - 477
IS  - 3
SP  - 469
VL  - 57
UR  - conv_2214
ER  - 

@article{
author = "Džinčić, Igor and Skakić, Dušan",
year = "2012",
abstract = "Only a few studies were found in which joints are taken into consideration while analyzing spatial furniture by usage of finite element method. This paper presents results of effects of type of fit on strength of oval tenon-mortise. When calculation are to be made in solid-mechanics, specific input parameters must be defined. In most modern finite element software's Young's modulus of elasticity is one of the basic data. The type of strain, which is result of the fit with splice, has impact on the changes in the Young's modulus of elasticity, which is the basic parameter in the defining of the material of the model. Aim of this study is to define rate of deformation of oval tenon-mortise joint as a result of fitting influence. Type and size of strains which occur in a joint in case of the fit with splice were examined with templates which were set on a joint. Based on this study results, the type of fit has influence on strength of the joints. In the presence of the fit with splice, a permanent change in the dimensions of the plug and hole will occur. During joining of joints with a splice fit, most strains belong to the group of elastic strains, which by all means contributes to the joint strength.",
journal = "Wood Research",
title = "Influence of type of fit on strength and deformation of oval tenon-mortise joint",
pages = "477-469",
number = "3",
volume = "57",
url = "conv_2214"
}

Džinčić, I.,& Skakić, D.. (2012). Influence of type of fit on strength and deformation of oval tenon-mortise joint. in Wood Research, 57(3), 469-477.
conv_2214

Džinčić I, Skakić D. Influence of type of fit on strength and deformation of oval tenon-mortise joint. in Wood Research. 2012;57(3):469-477.
conv_2214 .

Džinčić, Igor, Skakić, Dušan, "Influence of type of fit on strength and deformation of oval tenon-mortise joint" in Wood Research, 57, no. 3 (2012):469-477,
conv_2214 .

TY  - JOUR
AU  - Džinčić, Igor
AU  - Skakić, Dušan
PY  - 2012
UR  - https://omorika.sfb.bg.ac.rs/handle/123456789/426
AB  - Machinability has been defined, in a general way, as an ability of a certain structural material to be machined by cutting or deformation through common, economical production techniques and technologies. However, a significant disadvantage of this definition is that it does not define the way in which this ability (machinability) is quantified and measured. This research deals with with ways of determining numerical values of parameters of machinability during the process of machining oak wood by longitudinal routing. In order to determine the factors of machinability in the function of tangential cutting force the authors used multifactor orthogonal linear plan of experiment. Analyzing the position of straight lines in the given diagrams and the values of the exponents in the model the following can be concluded: Average tangential cutting force increases with the increase of any of the analyzed factors; With regard to intensity, cutting depth has a greater effect on the cutting force; If the cutting depth increases, the increase of cutting force is faster when feed per edge is greater. If the feed per edge is increased, the increase of tangential cutting force is more significant when the value of cutting depth is greater.
T2  - Wood Research
T1  - Determining the parameters of wood machinability as a function of tangential cutting force during the process of machining wood by routing
EP  - 171
IS  - 1
SP  - 161
VL  - 57
UR  - conv_1019
ER  - 

@article{
author = "Džinčić, Igor and Skakić, Dušan",
year = "2012",
abstract = "Machinability has been defined, in a general way, as an ability of a certain structural material to be machined by cutting or deformation through common, economical production techniques and technologies. However, a significant disadvantage of this definition is that it does not define the way in which this ability (machinability) is quantified and measured. This research deals with with ways of determining numerical values of parameters of machinability during the process of machining oak wood by longitudinal routing. In order to determine the factors of machinability in the function of tangential cutting force the authors used multifactor orthogonal linear plan of experiment. Analyzing the position of straight lines in the given diagrams and the values of the exponents in the model the following can be concluded: Average tangential cutting force increases with the increase of any of the analyzed factors; With regard to intensity, cutting depth has a greater effect on the cutting force; If the cutting depth increases, the increase of cutting force is faster when feed per edge is greater. If the feed per edge is increased, the increase of tangential cutting force is more significant when the value of cutting depth is greater.",
journal = "Wood Research",
title = "Determining the parameters of wood machinability as a function of tangential cutting force during the process of machining wood by routing",
pages = "171-161",
number = "1",
volume = "57",
url = "conv_1019"
}

Džinčić, I.,& Skakić, D.. (2012). Determining the parameters of wood machinability as a function of tangential cutting force during the process of machining wood by routing. in Wood Research, 57(1), 161-171.
conv_1019

Džinčić I, Skakić D. Determining the parameters of wood machinability as a function of tangential cutting force during the process of machining wood by routing. in Wood Research. 2012;57(1):161-171.
conv_1019 .

Džinčić, Igor, Skakić, Dušan, "Determining the parameters of wood machinability as a function of tangential cutting force during the process of machining wood by routing" in Wood Research, 57, no. 1 (2012):161-171,
conv_1019 .

TY  - JOUR
AU  - Skakić, Dušan
AU  - Džinčić, Igor
PY  - 2009
UR  - https://omorika.sfb.bg.ac.rs/handle/123456789/273
AB  - Kvalitet proizvoda predstavlja ključ svake savremeno organizovane proizvodnje. U proizvodnoj praksi neophodno je uspostaviti optimalan odnos između kvaliteta, ekonomičnosti proizvodnje i rokova isporuke. Kvalitet nameštaja se vrednuje u tri nivoa kvaliteta: osnovni kvalitet, visoki kvalitet i posebno visoki kvalitet. Rezultati prikazani u okviru ovog rada su zasnovani na merenju pokazatelja kvaliteta stolica i stolova tokom 2007. i 2008. godine u Zavodu za kontrolu kvaliteta nameštaja.
AB  - The quality of products represents one of the key aims of any modern organized production. In the production practice, it is essential to establish the optimal relationship between quality, production economy and delivery deadlines. Furniture quality is evaluated by three levels and they are: basic quality, high quality and especially high quality. The results presented in this paper are based on the sample measurements of chairs and tables during 2007 and 2008 at the Institute for Furniture Quality Control.
PB  - Univerzitet u Beogradu - Šumarski fakultet, Beograd
T2  - Glasnik Šumarskog fakulteta
T1  - Karakteristike kvaliteta skeletnog nameštaja
T1  - Quality characteristics of spatial furniture
EP  - 145
IS  - 99
SP  - 135
DO  - 10.2298/GSF0999135S
UR  - conv_309
ER  - 

@article{
author = "Skakić, Dušan and Džinčić, Igor",
year = "2009",
abstract = "Kvalitet proizvoda predstavlja ključ svake savremeno organizovane proizvodnje. U proizvodnoj praksi neophodno je uspostaviti optimalan odnos između kvaliteta, ekonomičnosti proizvodnje i rokova isporuke. Kvalitet nameštaja se vrednuje u tri nivoa kvaliteta: osnovni kvalitet, visoki kvalitet i posebno visoki kvalitet. Rezultati prikazani u okviru ovog rada su zasnovani na merenju pokazatelja kvaliteta stolica i stolova tokom 2007. i 2008. godine u Zavodu za kontrolu kvaliteta nameštaja., The quality of products represents one of the key aims of any modern organized production. In the production practice, it is essential to establish the optimal relationship between quality, production economy and delivery deadlines. Furniture quality is evaluated by three levels and they are: basic quality, high quality and especially high quality. The results presented in this paper are based on the sample measurements of chairs and tables during 2007 and 2008 at the Institute for Furniture Quality Control.",
publisher = "Univerzitet u Beogradu - Šumarski fakultet, Beograd",
journal = "Glasnik Šumarskog fakulteta",
title = "Karakteristike kvaliteta skeletnog nameštaja, Quality characteristics of spatial furniture",
pages = "145-135",
number = "99",
doi = "10.2298/GSF0999135S",
url = "conv_309"
}

Skakić, D.,& Džinčić, I.. (2009). Karakteristike kvaliteta skeletnog nameštaja. in Glasnik Šumarskog fakulteta
Univerzitet u Beogradu - Šumarski fakultet, Beograd.(99), 135-145.
https://doi.org/10.2298/GSF0999135S
conv_309

Skakić D, Džinčić I. Karakteristike kvaliteta skeletnog nameštaja. in Glasnik Šumarskog fakulteta. 2009;(99):135-145.
doi:10.2298/GSF0999135S
conv_309 .

Skakić, Dušan, Džinčić, Igor, "Karakteristike kvaliteta skeletnog nameštaja" in Glasnik Šumarskog fakulteta, no. 99 (2009):135-145,
https://doi.org/10.2298/GSF0999135S .,
conv_309 .

TY  - JOUR
AU  - Skakić, Dušan
AU  - Džinčić, Igor
PY  - 2009
UR  - https://omorika.sfb.bg.ac.rs/handle/123456789/272
AB  - Rezultati naučnih istraživanja i iskustva iz inženjerske prakse nam ukazuju da definisanje konstrukcije zahteva veliki broj različitih konstruktivnih rešenja. Proces donošenja odluke često zahteva dosta vremena pri čemu ne rezultuje uvek optimalnim rešenjem. Iz ovih razloga se metod numeričke optimizacije koristi u iznalaženju najboljeg rešenja u velikom broju tehničkih nauka. Prvi korak u rešavanju problema pomoću metode konačnih elemenata je definisanje tipa stolice koji će se modelirati i definisanje dimenzija njenih sastavnih elemenata.
AB  - Both the scientific experience and the engineering practice indicate that the decision making processes in the course of solving complex designing problems require an analysis of a great number of different construction variants. These types of decision-making processes are time consuming and do not always result in the selection of an optimal solution. That is why the methods of numerical optimization are applied in a wide range of technical sciences to assist in the selection of the best solution. The first step in solving the problem by using the Finite element method is to determine the type of chair earmarked for modeling, and to determine the dimensions of the chair elements.
PB  - Univerzitet u Beogradu - Šumarski fakultet, Beograd
T2  - Glasnik Šumarskog fakulteta
T1  - Grupisanje i analiza kvaliteta stolica i njihovih osnovnih sastavnih delova
T1  - Grouping and analysis of chair quality and their basic elements
EP  - 154
IS  - 99
SP  - 147
DO  - 10.2298/GSF0999147S
UR  - conv_310
ER  - 

@article{
author = "Skakić, Dušan and Džinčić, Igor",
year = "2009",
abstract = "Rezultati naučnih istraživanja i iskustva iz inženjerske prakse nam ukazuju da definisanje konstrukcije zahteva veliki broj različitih konstruktivnih rešenja. Proces donošenja odluke često zahteva dosta vremena pri čemu ne rezultuje uvek optimalnim rešenjem. Iz ovih razloga se metod numeričke optimizacije koristi u iznalaženju najboljeg rešenja u velikom broju tehničkih nauka. Prvi korak u rešavanju problema pomoću metode konačnih elemenata je definisanje tipa stolice koji će se modelirati i definisanje dimenzija njenih sastavnih elemenata., Both the scientific experience and the engineering practice indicate that the decision making processes in the course of solving complex designing problems require an analysis of a great number of different construction variants. These types of decision-making processes are time consuming and do not always result in the selection of an optimal solution. That is why the methods of numerical optimization are applied in a wide range of technical sciences to assist in the selection of the best solution. The first step in solving the problem by using the Finite element method is to determine the type of chair earmarked for modeling, and to determine the dimensions of the chair elements.",
publisher = "Univerzitet u Beogradu - Šumarski fakultet, Beograd",
journal = "Glasnik Šumarskog fakulteta",
title = "Grupisanje i analiza kvaliteta stolica i njihovih osnovnih sastavnih delova, Grouping and analysis of chair quality and their basic elements",
pages = "154-147",
number = "99",
doi = "10.2298/GSF0999147S",
url = "conv_310"
}

Skakić, D.,& Džinčić, I.. (2009). Grupisanje i analiza kvaliteta stolica i njihovih osnovnih sastavnih delova. in Glasnik Šumarskog fakulteta
Univerzitet u Beogradu - Šumarski fakultet, Beograd.(99), 147-154.
https://doi.org/10.2298/GSF0999147S
conv_310

Skakić D, Džinčić I. Grupisanje i analiza kvaliteta stolica i njihovih osnovnih sastavnih delova. in Glasnik Šumarskog fakulteta. 2009;(99):147-154.
doi:10.2298/GSF0999147S
conv_310 .

Skakić, Dušan, Džinčić, Igor, "Grupisanje i analiza kvaliteta stolica i njihovih osnovnih sastavnih delova" in Glasnik Šumarskog fakulteta, no. 99 (2009):147-154,
https://doi.org/10.2298/GSF0999147S .,
conv_310 .

TY  - JOUR
AU  - Džinčić, Igor
AU  - Skakić, Dušan
AU  - Nestorović, Biserka
PY  - 2008
UR  - https://omorika.sfb.bg.ac.rs/handle/123456789/238
AB  - Kroz praksu se pokazalo da je trajnost stolica najvećim delom u funkciji izdržljivosti i izboru elemenata veze za različite konstrukcije stolica. Da bi se moglo vršiti upoređivanje stolica na osnovu izdržljivosti, a zbog različitih vrsta konstrukcije stolica, izvršena je njihova podela na 6 grupa, a prema načinu spajanja u kritičnim tačkama. Na čvrstoću kritičnog spoja utiču površina lepljenja, tačnost izrade, vid naleganja, vrsta i vlažnost drvnog materijala, kvalitet lepka i režimi lepljenja. Istraživanje uticajnih faktora na čvrstoću kritičnog spoja izvršeno je na dve grupe stolica sa sargovima i na dve grupe detalja koji čine kritične spojeve. Prilikom izrade uzoraka za ispitivanje varirani su sledeći uticajni faktori: tačnost izrade, vid naleganja i površina lepljenja.
AB  - Strength and durability of different types of chairs is mostly function of rigidity and type of joints. Classification of chairs was completed upon their critical points. Based on this divide, chairs were classified into six categories. Based on previous research, strength of joints have been influenced by gluing surface, machining quality, type of fit, species and humidity of wood material, glue quality and gluing parameters. Research have been carried out on two groups of chairs, and two groups of joints. Machining quality, type of fit and gluing surface, have been varied during experiment.
PB  - Univerzitet u Beogradu - Šumarski fakultet, Beograd
T2  - Glasnik Šumarskog fakulteta
T1  - Uticajni faktori na čvrstoću i trajnost stolica
T1  - Factors affecting rigidity and durability of chairs
EP  - 275
IS  - 97
SP  - 259
DO  - 10.2298/GSF0897259D
UR  - conv_279
ER  - 

@article{
author = "Džinčić, Igor and Skakić, Dušan and Nestorović, Biserka",
year = "2008",
abstract = "Kroz praksu se pokazalo da je trajnost stolica najvećim delom u funkciji izdržljivosti i izboru elemenata veze za različite konstrukcije stolica. Da bi se moglo vršiti upoređivanje stolica na osnovu izdržljivosti, a zbog različitih vrsta konstrukcije stolica, izvršena je njihova podela na 6 grupa, a prema načinu spajanja u kritičnim tačkama. Na čvrstoću kritičnog spoja utiču površina lepljenja, tačnost izrade, vid naleganja, vrsta i vlažnost drvnog materijala, kvalitet lepka i režimi lepljenja. Istraživanje uticajnih faktora na čvrstoću kritičnog spoja izvršeno je na dve grupe stolica sa sargovima i na dve grupe detalja koji čine kritične spojeve. Prilikom izrade uzoraka za ispitivanje varirani su sledeći uticajni faktori: tačnost izrade, vid naleganja i površina lepljenja., Strength and durability of different types of chairs is mostly function of rigidity and type of joints. Classification of chairs was completed upon their critical points. Based on this divide, chairs were classified into six categories. Based on previous research, strength of joints have been influenced by gluing surface, machining quality, type of fit, species and humidity of wood material, glue quality and gluing parameters. Research have been carried out on two groups of chairs, and two groups of joints. Machining quality, type of fit and gluing surface, have been varied during experiment.",
publisher = "Univerzitet u Beogradu - Šumarski fakultet, Beograd",
journal = "Glasnik Šumarskog fakulteta",
title = "Uticajni faktori na čvrstoću i trajnost stolica, Factors affecting rigidity and durability of chairs",
pages = "275-259",
number = "97",
doi = "10.2298/GSF0897259D",
url = "conv_279"
}

Džinčić, I., Skakić, D.,& Nestorović, B.. (2008). Uticajni faktori na čvrstoću i trajnost stolica. in Glasnik Šumarskog fakulteta
Univerzitet u Beogradu - Šumarski fakultet, Beograd.(97), 259-275.
https://doi.org/10.2298/GSF0897259D
conv_279

Džinčić I, Skakić D, Nestorović B. Uticajni faktori na čvrstoću i trajnost stolica. in Glasnik Šumarskog fakulteta. 2008;(97):259-275.
doi:10.2298/GSF0897259D
conv_279 .

Džinčić, Igor, Skakić, Dušan, Nestorović, Biserka, "Uticajni faktori na čvrstoću i trajnost stolica" in Glasnik Šumarskog fakulteta, no. 97 (2008):259-275,
https://doi.org/10.2298/GSF0897259D .,
conv_279 .

TY  - JOUR
AU  - Skakić, Dušan
AU  - Džinčić, Igor
PY  - 2008
UR  - https://omorika.sfb.bg.ac.rs/handle/123456789/245
AB  - U radu su saopšteni rezultati uporednih istraživanja čvrstoće stolica koje su izrađene od drveta Paulownia tomentosa i drveta bukve. Kao predstavnik nameštaja na kome je sprovedeno ispitivanje mogućnosti uvođenja nove vrste za proizvodnju nameštaja u pogone finalne prerade u Srbiji izabrana je stolica. U poređenju sa ostalim tipovima nameštaja statička i dinamička opterećenja kod stolica dostižu najveće vrednosti, tako da su ti pokazatelji bili presudni za odabir komada nameštaja na kome će biti izvršeni ispitivanje. Dobijeni rezultati upućuju na mogućnost korišćenja ove vrste drveta za proizvodnju nameštaja koji u toku eksploatacije nije izložen velikim opterećenjima.
AB  - The result of parallel investigation of chair durability, which has been made in two different wood species (beach and Paulwonia tomentosa) has been presented in this paper. Static and dynamic loads has highest values in seating furniture, and that is the reason why chair has been chosen to bee representative for testing new species, which could be used in furniture production in Serbia. A shown results indicates on possibility that this species can be used only for production furniture which wont bee imposed with heavy loads during exploitation.
PB  - Univerzitet u Beogradu - Šumarski fakultet, Beograd
T2  - Glasnik Šumarskog fakulteta
T1  - Uporedno istraživanje čvrstoće stolica izrađenih od bukovine i Paulownie tomentose
T1  - Comparative investigation of durability of chairs made of beach and Paulownia tomentosa
EP  - 176
IS  - 98
SP  - 167
DO  - 10.2298/GSF0898167S
UR  - conv_288
ER  - 

@article{
author = "Skakić, Dušan and Džinčić, Igor",
year = "2008",
abstract = "U radu su saopšteni rezultati uporednih istraživanja čvrstoće stolica koje su izrađene od drveta Paulownia tomentosa i drveta bukve. Kao predstavnik nameštaja na kome je sprovedeno ispitivanje mogućnosti uvođenja nove vrste za proizvodnju nameštaja u pogone finalne prerade u Srbiji izabrana je stolica. U poređenju sa ostalim tipovima nameštaja statička i dinamička opterećenja kod stolica dostižu najveće vrednosti, tako da su ti pokazatelji bili presudni za odabir komada nameštaja na kome će biti izvršeni ispitivanje. Dobijeni rezultati upućuju na mogućnost korišćenja ove vrste drveta za proizvodnju nameštaja koji u toku eksploatacije nije izložen velikim opterećenjima., The result of parallel investigation of chair durability, which has been made in two different wood species (beach and Paulwonia tomentosa) has been presented in this paper. Static and dynamic loads has highest values in seating furniture, and that is the reason why chair has been chosen to bee representative for testing new species, which could be used in furniture production in Serbia. A shown results indicates on possibility that this species can be used only for production furniture which wont bee imposed with heavy loads during exploitation.",
publisher = "Univerzitet u Beogradu - Šumarski fakultet, Beograd",
journal = "Glasnik Šumarskog fakulteta",
title = "Uporedno istraživanje čvrstoće stolica izrađenih od bukovine i Paulownie tomentose, Comparative investigation of durability of chairs made of beach and Paulownia tomentosa",
pages = "176-167",
number = "98",
doi = "10.2298/GSF0898167S",
url = "conv_288"
}

Skakić, D.,& Džinčić, I.. (2008). Uporedno istraživanje čvrstoće stolica izrađenih od bukovine i Paulownie tomentose. in Glasnik Šumarskog fakulteta
Univerzitet u Beogradu - Šumarski fakultet, Beograd.(98), 167-176.
https://doi.org/10.2298/GSF0898167S
conv_288

Skakić D, Džinčić I. Uporedno istraživanje čvrstoće stolica izrađenih od bukovine i Paulownie tomentose. in Glasnik Šumarskog fakulteta. 2008;(98):167-176.
doi:10.2298/GSF0898167S
conv_288 .

Skakić, Dušan, Džinčić, Igor, "Uporedno istraživanje čvrstoće stolica izrađenih od bukovine i Paulownie tomentose" in Glasnik Šumarskog fakulteta, no. 98 (2008):167-176,
https://doi.org/10.2298/GSF0898167S .,
conv_288 .

TY  - JOUR
AU  - Skakić, Dušan
AU  - Džinčić, Igor
AU  - Nestorović, Biserka
AU  - Palija, Tanja
PY  - 2008
UR  - https://omorika.sfb.bg.ac.rs/handle/123456789/236
AB  - Kvalitet proizvoda predstavlja jedan od ključnih ciljeva svake savremeno organizovane proizvodnje, što ga svrstava u grupu osnovnih izlaznih karakteristika proizvodnog procesa. Prema nacionalnom standardu ocena kvaliteta nameštaja se donosi na osnovu ispitivanja karakteristika kvaliteta koje su podeljene u četiri grupe uslova: funkcionalnost (funkcionalne mere i stabilnost), izdržljivost, otpornost površina i kvalitet materijala i tačnost izrade. U ovom radu ispitan je kvalitet trpezarijske stolice pri čemu su korišćeni različiti elementi veze i dati su predlozi za poboljšanje konstrukcije. Dve grupe stolica su izrađene uz pomoć montažno-demontažnih spojeva, dok je jedna grupa uzoraka spajana pomoću stolarskih spojeva uz upotrebu lepka.
AB  - Products quality presents one of the main causes of every contemporary organized production, which includes it, in group of basic exit characteristics. According to national standard, quality mark is based on testing of its quality characteristics. A characteristic of quality has been divided into four groups of demands: functionality (functional dimensions and stability tests), rigidity, surface rigidity, quality of materials and work piece accuracy. Dining chair has been investigated by use of different wood joints, and some remarks on construction has been given. Two groups of investigated chairs has been mounted by use of metal fittings, and one group has been connected with wood dowels by use of PVA wood glue.
PB  - Univerzitet u Beogradu - Šumarski fakultet, Beograd
T2  - Glasnik Šumarskog fakulteta
T1  - Uticaj različitih elemenata veze na kvalitet trpezarijskih stolica
T1  - Influence of different joints on quality of dining chairs
EP  - 247
IS  - 97
SP  - 235
DO  - 10.2298/GSF0897235S
UR  - conv_277
ER  - 

@article{
author = "Skakić, Dušan and Džinčić, Igor and Nestorović, Biserka and Palija, Tanja",
year = "2008",
abstract = "Kvalitet proizvoda predstavlja jedan od ključnih ciljeva svake savremeno organizovane proizvodnje, što ga svrstava u grupu osnovnih izlaznih karakteristika proizvodnog procesa. Prema nacionalnom standardu ocena kvaliteta nameštaja se donosi na osnovu ispitivanja karakteristika kvaliteta koje su podeljene u četiri grupe uslova: funkcionalnost (funkcionalne mere i stabilnost), izdržljivost, otpornost površina i kvalitet materijala i tačnost izrade. U ovom radu ispitan je kvalitet trpezarijske stolice pri čemu su korišćeni različiti elementi veze i dati su predlozi za poboljšanje konstrukcije. Dve grupe stolica su izrađene uz pomoć montažno-demontažnih spojeva, dok je jedna grupa uzoraka spajana pomoću stolarskih spojeva uz upotrebu lepka., Products quality presents one of the main causes of every contemporary organized production, which includes it, in group of basic exit characteristics. According to national standard, quality mark is based on testing of its quality characteristics. A characteristic of quality has been divided into four groups of demands: functionality (functional dimensions and stability tests), rigidity, surface rigidity, quality of materials and work piece accuracy. Dining chair has been investigated by use of different wood joints, and some remarks on construction has been given. Two groups of investigated chairs has been mounted by use of metal fittings, and one group has been connected with wood dowels by use of PVA wood glue.",
publisher = "Univerzitet u Beogradu - Šumarski fakultet, Beograd",
journal = "Glasnik Šumarskog fakulteta",
title = "Uticaj različitih elemenata veze na kvalitet trpezarijskih stolica, Influence of different joints on quality of dining chairs",
pages = "247-235",
number = "97",
doi = "10.2298/GSF0897235S",
url = "conv_277"
}

Skakić, D., Džinčić, I., Nestorović, B.,& Palija, T.. (2008). Uticaj različitih elemenata veze na kvalitet trpezarijskih stolica. in Glasnik Šumarskog fakulteta
Univerzitet u Beogradu - Šumarski fakultet, Beograd.(97), 235-247.
https://doi.org/10.2298/GSF0897235S
conv_277

Skakić D, Džinčić I, Nestorović B, Palija T. Uticaj različitih elemenata veze na kvalitet trpezarijskih stolica. in Glasnik Šumarskog fakulteta. 2008;(97):235-247.
doi:10.2298/GSF0897235S
conv_277 .

Skakić, Dušan, Džinčić, Igor, Nestorović, Biserka, Palija, Tanja, "Uticaj različitih elemenata veze na kvalitet trpezarijskih stolica" in Glasnik Šumarskog fakulteta, no. 97 (2008):235-247,
https://doi.org/10.2298/GSF0897235S .,
conv_277 .