TY  - JOUR
AU  - Džinčić, Igor
AU  - Palija, Tanja
AU  - Zivanić, Dragan
AU  - Dacić, Vojislav
PY  - 2021
UR  - https://omorika.sfb.bg.ac.rs/handle/123456789/1197
AB  - The objective of this study was to investigate the relation of diameter of pilot hole and screw, and machining accuracy on withdrawal strengths of the screws and durability of the dining tables. For this purpose, fasteners and material types on the failure loads of dining table corner joints have been analyzed experimentally and statistically. Double ended thread bolts with different drilling regimes have been used as fastener types. A parallel investigation of rigidity and durability of tables, and withdrawal capacities in accordance with the according to current norms, was performed. According to the results, it is concluded that the diameter of the drilled hole significantly influences the value of the withdrawal strengths of the screws. By analyzing the effect of drilling diameter on the rigidity of tables, a statistically significant difference was determined. As the drilling diameter increases, the rigidity of the examined dining tables decreases.
T2  - Maderas-Ciencia Y Tecnologia
T1  - Determination of the strength performance of table frames
VL  - 23
DO  - 10.4067/s0718-221x2021000100461
UR  - conv_1600
ER  - 

@article{
author = "Džinčić, Igor and Palija, Tanja and Zivanić, Dragan and Dacić, Vojislav",
year = "2021",
abstract = "The objective of this study was to investigate the relation of diameter of pilot hole and screw, and machining accuracy on withdrawal strengths of the screws and durability of the dining tables. For this purpose, fasteners and material types on the failure loads of dining table corner joints have been analyzed experimentally and statistically. Double ended thread bolts with different drilling regimes have been used as fastener types. A parallel investigation of rigidity and durability of tables, and withdrawal capacities in accordance with the according to current norms, was performed. According to the results, it is concluded that the diameter of the drilled hole significantly influences the value of the withdrawal strengths of the screws. By analyzing the effect of drilling diameter on the rigidity of tables, a statistically significant difference was determined. As the drilling diameter increases, the rigidity of the examined dining tables decreases.",
journal = "Maderas-Ciencia Y Tecnologia",
title = "Determination of the strength performance of table frames",
volume = "23",
doi = "10.4067/s0718-221x2021000100461",
url = "conv_1600"
}

Džinčić, I., Palija, T., Zivanić, D.,& Dacić, V.. (2021). Determination of the strength performance of table frames. in Maderas-Ciencia Y Tecnologia, 23.
https://doi.org/10.4067/s0718-221x2021000100461
conv_1600

Džinčić I, Palija T, Zivanić D, Dacić V. Determination of the strength performance of table frames. in Maderas-Ciencia Y Tecnologia. 2021;23.
doi:10.4067/s0718-221x2021000100461
conv_1600 .

Džinčić, Igor, Palija, Tanja, Zivanić, Dragan, Dacić, Vojislav, "Determination of the strength performance of table frames" in Maderas-Ciencia Y Tecnologia, 23 (2021),
https://doi.org/10.4067/s0718-221x2021000100461 .,
conv_1600 .

TY  - JOUR
AU  - Džinčić, Igor
AU  - Nestorović, Biserka
AU  - Dacić, Vojislav
PY  - 2016
UR  - https://omorika.sfb.bg.ac.rs/handle/123456789/739
AB  - U radu su prikazani rezultati uporednog ispitivanja čvrstoće spojeva ovalni čep-žljeb kod dve grupe proba. Spojevi grupe A, izrađivani su sa oba ramena čepa, dok su spojevi grupe B izrađivani bez donjeg ramena čepa. Ispitivanje čvrstoće, sprovedeno je na spojevima bočnog sarga i zadnje noge stolice. Rezultati istraživanja su pokazali da spojevi grupe A imaju veću prosečnu vrednost momenta savijanja u odnosu na spojeve grupe B, ali statističkom analizom nije potvrđena značajnost razlike u čvrstoći između ove dve grupe spojeva.
AB  - This paper presents the results of a parallel examination on the strength of oval tenonmortise joints in two groups of test joints. Joints from group A were made with both shoulders of tenon, while joints from group B were made without the lower shoulder. Examination of strength was conducted on a chair joints rear leg-rail. The results of the examination indicated that joints in group A had a higher average bending moment capacity in comparison with the joints in group B. However, the significance of difference in strength between the two groups of joints was not confirmed by the statistical analysis.
PB  - Univerzitet u Beogradu - Šumarski fakultet, Beograd
T2  - Glasnik Šumarskog fakulteta
T1  - Uticaj ramena čepa na čvrstoću spoja ovalni čep-žljeb
T1  - The effect of shoulder on the strength of the oval tenon-mortise joint
EP  - 46
IS  - 113
SP  - 35
DO  - 10.2298/GSF151109001D
UR  - conv_435
ER  - 

@article{
author = "Džinčić, Igor and Nestorović, Biserka and Dacić, Vojislav",
year = "2016",
abstract = "U radu su prikazani rezultati uporednog ispitivanja čvrstoće spojeva ovalni čep-žljeb kod dve grupe proba. Spojevi grupe A, izrađivani su sa oba ramena čepa, dok su spojevi grupe B izrađivani bez donjeg ramena čepa. Ispitivanje čvrstoće, sprovedeno je na spojevima bočnog sarga i zadnje noge stolice. Rezultati istraživanja su pokazali da spojevi grupe A imaju veću prosečnu vrednost momenta savijanja u odnosu na spojeve grupe B, ali statističkom analizom nije potvrđena značajnost razlike u čvrstoći između ove dve grupe spojeva., This paper presents the results of a parallel examination on the strength of oval tenonmortise joints in two groups of test joints. Joints from group A were made with both shoulders of tenon, while joints from group B were made without the lower shoulder. Examination of strength was conducted on a chair joints rear leg-rail. The results of the examination indicated that joints in group A had a higher average bending moment capacity in comparison with the joints in group B. However, the significance of difference in strength between the two groups of joints was not confirmed by the statistical analysis.",
publisher = "Univerzitet u Beogradu - Šumarski fakultet, Beograd",
journal = "Glasnik Šumarskog fakulteta",
title = "Uticaj ramena čepa na čvrstoću spoja ovalni čep-žljeb, The effect of shoulder on the strength of the oval tenon-mortise joint",
pages = "46-35",
number = "113",
doi = "10.2298/GSF151109001D",
url = "conv_435"
}

Džinčić, I., Nestorović, B.,& Dacić, V.. (2016). Uticaj ramena čepa na čvrstoću spoja ovalni čep-žljeb. in Glasnik Šumarskog fakulteta
Univerzitet u Beogradu - Šumarski fakultet, Beograd.(113), 35-46.
https://doi.org/10.2298/GSF151109001D
conv_435

Džinčić I, Nestorović B, Dacić V. Uticaj ramena čepa na čvrstoću spoja ovalni čep-žljeb. in Glasnik Šumarskog fakulteta. 2016;(113):35-46.
doi:10.2298/GSF151109001D
conv_435 .

Džinčić, Igor, Nestorović, Biserka, Dacić, Vojislav, "Uticaj ramena čepa na čvrstoću spoja ovalni čep-žljeb" in Glasnik Šumarskog fakulteta, no. 113 (2016):35-46,
https://doi.org/10.2298/GSF151109001D .,
conv_435 .