TY  - JOUR
AU  - Džinčić, Igor
AU  - Nestorović, Biserka
AU  - Dacić, Vojislav
PY  - 2016
UR  - https://omorika.sfb.bg.ac.rs/handle/123456789/739
AB  - U radu su prikazani rezultati uporednog ispitivanja čvrstoće spojeva ovalni čep-žljeb kod dve grupe proba. Spojevi grupe A, izrađivani su sa oba ramena čepa, dok su spojevi grupe B izrađivani bez donjeg ramena čepa. Ispitivanje čvrstoće, sprovedeno je na spojevima bočnog sarga i zadnje noge stolice. Rezultati istraživanja su pokazali da spojevi grupe A imaju veću prosečnu vrednost momenta savijanja u odnosu na spojeve grupe B, ali statističkom analizom nije potvrđena značajnost razlike u čvrstoći između ove dve grupe spojeva.
AB  - This paper presents the results of a parallel examination on the strength of oval tenonmortise joints in two groups of test joints. Joints from group A were made with both shoulders of tenon, while joints from group B were made without the lower shoulder. Examination of strength was conducted on a chair joints rear leg-rail. The results of the examination indicated that joints in group A had a higher average bending moment capacity in comparison with the joints in group B. However, the significance of difference in strength between the two groups of joints was not confirmed by the statistical analysis.
PB  - Univerzitet u Beogradu - Šumarski fakultet, Beograd
T2  - Glasnik Šumarskog fakulteta
T1  - Uticaj ramena čepa na čvrstoću spoja ovalni čep-žljeb
T1  - The effect of shoulder on the strength of the oval tenon-mortise joint
EP  - 46
IS  - 113
SP  - 35
DO  - 10.2298/GSF151109001D
UR  - conv_435
ER  - 

@article{
author = "Džinčić, Igor and Nestorović, Biserka and Dacić, Vojislav",
year = "2016",
abstract = "U radu su prikazani rezultati uporednog ispitivanja čvrstoće spojeva ovalni čep-žljeb kod dve grupe proba. Spojevi grupe A, izrađivani su sa oba ramena čepa, dok su spojevi grupe B izrađivani bez donjeg ramena čepa. Ispitivanje čvrstoće, sprovedeno je na spojevima bočnog sarga i zadnje noge stolice. Rezultati istraživanja su pokazali da spojevi grupe A imaju veću prosečnu vrednost momenta savijanja u odnosu na spojeve grupe B, ali statističkom analizom nije potvrđena značajnost razlike u čvrstoći između ove dve grupe spojeva., This paper presents the results of a parallel examination on the strength of oval tenonmortise joints in two groups of test joints. Joints from group A were made with both shoulders of tenon, while joints from group B were made without the lower shoulder. Examination of strength was conducted on a chair joints rear leg-rail. The results of the examination indicated that joints in group A had a higher average bending moment capacity in comparison with the joints in group B. However, the significance of difference in strength between the two groups of joints was not confirmed by the statistical analysis.",
publisher = "Univerzitet u Beogradu - Šumarski fakultet, Beograd",
journal = "Glasnik Šumarskog fakulteta",
title = "Uticaj ramena čepa na čvrstoću spoja ovalni čep-žljeb, The effect of shoulder on the strength of the oval tenon-mortise joint",
pages = "46-35",
number = "113",
doi = "10.2298/GSF151109001D",
url = "conv_435"
}

Džinčić, I., Nestorović, B.,& Dacić, V.. (2016). Uticaj ramena čepa na čvrstoću spoja ovalni čep-žljeb. in Glasnik Šumarskog fakulteta
Univerzitet u Beogradu - Šumarski fakultet, Beograd.(113), 35-46.
https://doi.org/10.2298/GSF151109001D
conv_435

Džinčić I, Nestorović B, Dacić V. Uticaj ramena čepa na čvrstoću spoja ovalni čep-žljeb. in Glasnik Šumarskog fakulteta. 2016;(113):35-46.
doi:10.2298/GSF151109001D
conv_435 .

Džinčić, Igor, Nestorović, Biserka, Dacić, Vojislav, "Uticaj ramena čepa na čvrstoću spoja ovalni čep-žljeb" in Glasnik Šumarskog fakulteta, no. 113 (2016):35-46,
https://doi.org/10.2298/GSF151109001D .,
conv_435 .

TY  - CONF
AU  - Burda, Aleksandra
AU  - Matić, Jelena
AU  - Nestorović, Biserka
PY  - 2015
UR  - https://omorika.sfb.bg.ac.rs/handle/123456789/713
AB  - Architectural acoustics can be defined as a acoustic quality of buildings. Sound insulation is part of the general building quality and is based on human hearing mechanism and purpose of space. In accordance with the results of acoustical measurements, sound insulation is achieved by designing appropriate geometry of a room and appropriate building materialization in which wood has important role. Wood and wood-based materials are widely used in interior architecture and this paper is concerned with the role of wood and wood-based products from the point of the acoustical project in interior design. Elements of sound insulation based on wood and their effectiveness are analyzed and shown through conclusions and recommendations for architects from the point of designing space, construction elements, windows, doors, floor coverings, walls and ceilings.
PB  - University of Zagreb - Faculty of Forestry
C3  - 26th International Conference on Wood Science and Technology, ICWST 2015: Implementation of Wood Science in Woodworking Sector - Proceedings
T1  - Use of Wood in Architectural Acoustics
EP  - 59
SP  - 53
UR  - conv_2132
ER  - 

@conference{
author = "Burda, Aleksandra and Matić, Jelena and Nestorović, Biserka",
year = "2015",
abstract = "Architectural acoustics can be defined as a acoustic quality of buildings. Sound insulation is part of the general building quality and is based on human hearing mechanism and purpose of space. In accordance with the results of acoustical measurements, sound insulation is achieved by designing appropriate geometry of a room and appropriate building materialization in which wood has important role. Wood and wood-based materials are widely used in interior architecture and this paper is concerned with the role of wood and wood-based products from the point of the acoustical project in interior design. Elements of sound insulation based on wood and their effectiveness are analyzed and shown through conclusions and recommendations for architects from the point of designing space, construction elements, windows, doors, floor coverings, walls and ceilings.",
publisher = "University of Zagreb - Faculty of Forestry",
journal = "26th International Conference on Wood Science and Technology, ICWST 2015: Implementation of Wood Science in Woodworking Sector - Proceedings",
title = "Use of Wood in Architectural Acoustics",
pages = "59-53",
url = "conv_2132"
}

Burda, A., Matić, J.,& Nestorović, B.. (2015). Use of Wood in Architectural Acoustics. in 26th International Conference on Wood Science and Technology, ICWST 2015: Implementation of Wood Science in Woodworking Sector - Proceedings
University of Zagreb - Faculty of Forestry., 53-59.
conv_2132

Burda A, Matić J, Nestorović B. Use of Wood in Architectural Acoustics. in 26th International Conference on Wood Science and Technology, ICWST 2015: Implementation of Wood Science in Woodworking Sector - Proceedings. 2015;:53-59.
conv_2132 .

Burda, Aleksandra, Matić, Jelena, Nestorović, Biserka, "Use of Wood in Architectural Acoustics" in 26th International Conference on Wood Science and Technology, ICWST 2015: Implementation of Wood Science in Woodworking Sector - Proceedings (2015):53-59,
conv_2132 .

TY  - JOUR
AU  - Džinčić, Igor
AU  - Skakić, Dušan
AU  - Nestorović, Biserka
PY  - 2008
UR  - https://omorika.sfb.bg.ac.rs/handle/123456789/238
AB  - Kroz praksu se pokazalo da je trajnost stolica najvećim delom u funkciji izdržljivosti i izboru elemenata veze za različite konstrukcije stolica. Da bi se moglo vršiti upoređivanje stolica na osnovu izdržljivosti, a zbog različitih vrsta konstrukcije stolica, izvršena je njihova podela na 6 grupa, a prema načinu spajanja u kritičnim tačkama. Na čvrstoću kritičnog spoja utiču površina lepljenja, tačnost izrade, vid naleganja, vrsta i vlažnost drvnog materijala, kvalitet lepka i režimi lepljenja. Istraživanje uticajnih faktora na čvrstoću kritičnog spoja izvršeno je na dve grupe stolica sa sargovima i na dve grupe detalja koji čine kritične spojeve. Prilikom izrade uzoraka za ispitivanje varirani su sledeći uticajni faktori: tačnost izrade, vid naleganja i površina lepljenja.
AB  - Strength and durability of different types of chairs is mostly function of rigidity and type of joints. Classification of chairs was completed upon their critical points. Based on this divide, chairs were classified into six categories. Based on previous research, strength of joints have been influenced by gluing surface, machining quality, type of fit, species and humidity of wood material, glue quality and gluing parameters. Research have been carried out on two groups of chairs, and two groups of joints. Machining quality, type of fit and gluing surface, have been varied during experiment.
PB  - Univerzitet u Beogradu - Šumarski fakultet, Beograd
T2  - Glasnik Šumarskog fakulteta
T1  - Uticajni faktori na čvrstoću i trajnost stolica
T1  - Factors affecting rigidity and durability of chairs
EP  - 275
IS  - 97
SP  - 259
DO  - 10.2298/GSF0897259D
UR  - conv_279
ER  - 

@article{
author = "Džinčić, Igor and Skakić, Dušan and Nestorović, Biserka",
year = "2008",
abstract = "Kroz praksu se pokazalo da je trajnost stolica najvećim delom u funkciji izdržljivosti i izboru elemenata veze za različite konstrukcije stolica. Da bi se moglo vršiti upoređivanje stolica na osnovu izdržljivosti, a zbog različitih vrsta konstrukcije stolica, izvršena je njihova podela na 6 grupa, a prema načinu spajanja u kritičnim tačkama. Na čvrstoću kritičnog spoja utiču površina lepljenja, tačnost izrade, vid naleganja, vrsta i vlažnost drvnog materijala, kvalitet lepka i režimi lepljenja. Istraživanje uticajnih faktora na čvrstoću kritičnog spoja izvršeno je na dve grupe stolica sa sargovima i na dve grupe detalja koji čine kritične spojeve. Prilikom izrade uzoraka za ispitivanje varirani su sledeći uticajni faktori: tačnost izrade, vid naleganja i površina lepljenja., Strength and durability of different types of chairs is mostly function of rigidity and type of joints. Classification of chairs was completed upon their critical points. Based on this divide, chairs were classified into six categories. Based on previous research, strength of joints have been influenced by gluing surface, machining quality, type of fit, species and humidity of wood material, glue quality and gluing parameters. Research have been carried out on two groups of chairs, and two groups of joints. Machining quality, type of fit and gluing surface, have been varied during experiment.",
publisher = "Univerzitet u Beogradu - Šumarski fakultet, Beograd",
journal = "Glasnik Šumarskog fakulteta",
title = "Uticajni faktori na čvrstoću i trajnost stolica, Factors affecting rigidity and durability of chairs",
pages = "275-259",
number = "97",
doi = "10.2298/GSF0897259D",
url = "conv_279"
}

Džinčić, I., Skakić, D.,& Nestorović, B.. (2008). Uticajni faktori na čvrstoću i trajnost stolica. in Glasnik Šumarskog fakulteta
Univerzitet u Beogradu - Šumarski fakultet, Beograd.(97), 259-275.
https://doi.org/10.2298/GSF0897259D
conv_279

Džinčić I, Skakić D, Nestorović B. Uticajni faktori na čvrstoću i trajnost stolica. in Glasnik Šumarskog fakulteta. 2008;(97):259-275.
doi:10.2298/GSF0897259D
conv_279 .

Džinčić, Igor, Skakić, Dušan, Nestorović, Biserka, "Uticajni faktori na čvrstoću i trajnost stolica" in Glasnik Šumarskog fakulteta, no. 97 (2008):259-275,
https://doi.org/10.2298/GSF0897259D .,
conv_279 .

TY  - JOUR
AU  - Skakić, Dušan
AU  - Džinčić, Igor
AU  - Nestorović, Biserka
AU  - Palija, Tanja
PY  - 2008
UR  - https://omorika.sfb.bg.ac.rs/handle/123456789/236
AB  - Kvalitet proizvoda predstavlja jedan od ključnih ciljeva svake savremeno organizovane proizvodnje, što ga svrstava u grupu osnovnih izlaznih karakteristika proizvodnog procesa. Prema nacionalnom standardu ocena kvaliteta nameštaja se donosi na osnovu ispitivanja karakteristika kvaliteta koje su podeljene u četiri grupe uslova: funkcionalnost (funkcionalne mere i stabilnost), izdržljivost, otpornost površina i kvalitet materijala i tačnost izrade. U ovom radu ispitan je kvalitet trpezarijske stolice pri čemu su korišćeni različiti elementi veze i dati su predlozi za poboljšanje konstrukcije. Dve grupe stolica su izrađene uz pomoć montažno-demontažnih spojeva, dok je jedna grupa uzoraka spajana pomoću stolarskih spojeva uz upotrebu lepka.
AB  - Products quality presents one of the main causes of every contemporary organized production, which includes it, in group of basic exit characteristics. According to national standard, quality mark is based on testing of its quality characteristics. A characteristic of quality has been divided into four groups of demands: functionality (functional dimensions and stability tests), rigidity, surface rigidity, quality of materials and work piece accuracy. Dining chair has been investigated by use of different wood joints, and some remarks on construction has been given. Two groups of investigated chairs has been mounted by use of metal fittings, and one group has been connected with wood dowels by use of PVA wood glue.
PB  - Univerzitet u Beogradu - Šumarski fakultet, Beograd
T2  - Glasnik Šumarskog fakulteta
T1  - Uticaj različitih elemenata veze na kvalitet trpezarijskih stolica
T1  - Influence of different joints on quality of dining chairs
EP  - 247
IS  - 97
SP  - 235
DO  - 10.2298/GSF0897235S
UR  - conv_277
ER  - 

@article{
author = "Skakić, Dušan and Džinčić, Igor and Nestorović, Biserka and Palija, Tanja",
year = "2008",
abstract = "Kvalitet proizvoda predstavlja jedan od ključnih ciljeva svake savremeno organizovane proizvodnje, što ga svrstava u grupu osnovnih izlaznih karakteristika proizvodnog procesa. Prema nacionalnom standardu ocena kvaliteta nameštaja se donosi na osnovu ispitivanja karakteristika kvaliteta koje su podeljene u četiri grupe uslova: funkcionalnost (funkcionalne mere i stabilnost), izdržljivost, otpornost površina i kvalitet materijala i tačnost izrade. U ovom radu ispitan je kvalitet trpezarijske stolice pri čemu su korišćeni različiti elementi veze i dati su predlozi za poboljšanje konstrukcije. Dve grupe stolica su izrađene uz pomoć montažno-demontažnih spojeva, dok je jedna grupa uzoraka spajana pomoću stolarskih spojeva uz upotrebu lepka., Products quality presents one of the main causes of every contemporary organized production, which includes it, in group of basic exit characteristics. According to national standard, quality mark is based on testing of its quality characteristics. A characteristic of quality has been divided into four groups of demands: functionality (functional dimensions and stability tests), rigidity, surface rigidity, quality of materials and work piece accuracy. Dining chair has been investigated by use of different wood joints, and some remarks on construction has been given. Two groups of investigated chairs has been mounted by use of metal fittings, and one group has been connected with wood dowels by use of PVA wood glue.",
publisher = "Univerzitet u Beogradu - Šumarski fakultet, Beograd",
journal = "Glasnik Šumarskog fakulteta",
title = "Uticaj različitih elemenata veze na kvalitet trpezarijskih stolica, Influence of different joints on quality of dining chairs",
pages = "247-235",
number = "97",
doi = "10.2298/GSF0897235S",
url = "conv_277"
}

Skakić, D., Džinčić, I., Nestorović, B.,& Palija, T.. (2008). Uticaj različitih elemenata veze na kvalitet trpezarijskih stolica. in Glasnik Šumarskog fakulteta
Univerzitet u Beogradu - Šumarski fakultet, Beograd.(97), 235-247.
https://doi.org/10.2298/GSF0897235S
conv_277

Skakić D, Džinčić I, Nestorović B, Palija T. Uticaj različitih elemenata veze na kvalitet trpezarijskih stolica. in Glasnik Šumarskog fakulteta. 2008;(97):235-247.
doi:10.2298/GSF0897235S
conv_277 .

Skakić, Dušan, Džinčić, Igor, Nestorović, Biserka, Palija, Tanja, "Uticaj različitih elemenata veze na kvalitet trpezarijskih stolica" in Glasnik Šumarskog fakulteta, no. 97 (2008):235-247,
https://doi.org/10.2298/GSF0897235S .,
conv_277 .